1 _______________________
2 BUILDING THE FSQA SUITE
3 _______________________
5 - cd into the xfstests directory
6 - install prerequisite packages
7 For example, for Ubuntu:
8 sudo apt-get install xfslibs-dev uuid-dev libtool-bin \
9 e2fsprogs automake gcc libuuid1 quota attr libattr1-dev make \
10 libacl1-dev libaio-dev xfsprogs libgdbm-dev gawk fio dbench \
11 uuid-runtime python sqlite3
12 For Fedora, RHEL, or CentOS:
13 yum install acl attr automake bc dbench dump e2fsprogs fio \
14 gawk gcc indent libtool lvm2 make psmisc quota sed \
16 libacl-devel libattr-devel libaio-devel libuuid-devel \
17 xfsprogs-devel btrfs-progs-devel python sqlite
18 (Older distributions may require xfsprogs-qa-devel as well.)
19 (Note that for RHEL and CentOS, you may need the EPEL repo.)
22 - create fsgqa test user ("sudo useradd fsgqa")
23 - create 123456-fsgqa test user ("sudo useradd 123456-fsgqa")
25 ______________________
27 ______________________
29 Preparing system for tests:
31 - compile XFS into your kernel or load XFS modules
32 - install administrative tools specific to the filesystem you wish to test
33 - If you wish to run the udf components of the suite install
34 mkudffs. Also download and build the Philips UDF Verification Software
35 from http://www.extra.research.philips.com/udf/, then copy the udf_test
36 binary to xfstests/src/. If you wish to disable UDF verification test
37 set the environment variable DISABLE_UDF_TEST to 1.
40 - create one or two partitions to use for testing
42 - format as XFS, mount & optionally populate with
44 - one SCRATCH partition (optional)
45 - leave empty and expect this partition to be clobbered
46 by some tests. If this is not provided, many tests will
48 (SCRATCH and TEST must be two DIFFERENT partitions)
50 - for btrfs only: some btrfs test cases will need 3 or more independent
51 SCRATCH disks which should be set using SCRATCH_DEV_POOL (for eg:
52 SCRATCH_DEV_POOL="/dev/sda /dev/sdb /dev/sdc") with which
53 SCRATCH_DEV should be unused by the tester, and for the legacy
54 support SCRATCH_DEV will be set to the first disk of the
55 SCRATCH_DEV_POOL by xfstests script.
57 - setup your environment
59 - copy local.config.example to local.config and edit as needed
61 - setenv TEST_DEV "device containing TEST PARTITION"
62 - setenv TEST_DIR "mount point of TEST PARTITION"
64 - setenv SCRATCH_DEV "device containing SCRATCH PARTITION" OR
65 (btrfs only) setenv SCRATCH_DEV_POOL "to 3 or more SCRATCH disks for
66 testing btrfs raid concepts"
67 - setenv SCRATCH_MNT "mount point for SCRATCH PARTITION"
68 - setenv TAPE_DEV "tape device for testing xfsdump"
69 - setenv RMT_TAPE_DEV "remote tape device for testing xfsdump"
70 - setenv RMT_IRIXTAPE_DEV "remote IRIX tape device for testing xfsdump"
71 - setenv SCRATCH_LOGDEV "device for scratch-fs external log"
72 - setenv SCRATCH_RTDEV "device for scratch-fs realtime data"
73 - setenv TEST_LOGDEV "device for test-fs external log"
74 - setenv TEST_RTDEV "device for test-fs realtime data"
75 - if TEST_LOGDEV and/or TEST_RTDEV, these will always be used.
76 - if SCRATCH_LOGDEV and/or SCRATCH_RTDEV, the USE_EXTERNAL
77 environment variable set to "yes" will enable their use.
78 - setenv DIFF_LENGTH "number of diff lines to print from a failed test",
79 by default 10, set to 0 to print the full diff
80 - setenv FSTYP "the filesystem you want to test", the filesystem
81 type is devised from the TEST_DEV device, but you may want to
82 override it; if unset, the default is 'xfs'
83 - setenv FSSTRESS_AVOID and/or FSX_AVOID, which contain options
84 added to the end of fsstresss and fsx invocations, respectively,
85 in case you wish to exclude certain operational modes from these
87 - set TEST_XFS_REPAIR_REBUILD=1 to have _check_xfs_filesystem
88 run xfs_repair -n to check the filesystem; xfs_repair to rebuild
89 metadata indexes; and xfs_repair -n (a third time) to check the
90 results of the rebuilding.
91 - xfs_scrub, if present, will always check the test and scratch
92 filesystems if they are still online at the end of the test.
93 It is no longer necessary to set TEST_XFS_SCRUB.
94 - setenv LOGWRITES_DEV to a block device to use for power fail
96 - setenv PERF_CONFIGNAME to a arbitrary string to be used for
97 identifying the test setup for running perf tests. This should
98 be different for each type of performance test you wish to run so
99 that relevant results are compared. For example 'spinningrust'
100 for configurations that use spinning disks and 'nvme' for tests
103 - or add a case to the switch in common/config assigning
104 these variables based on the hostname of your test
106 - or add these variables to a file called local.config and keep that
107 file in your workarea.
109 - if testing xfsdump, make sure the tape devices have a
110 tape which can be overwritten.
112 - make sure $TEST_DEV is a mounted XFS partition
113 - make sure that $SCRATCH_DEV or $SCRATCH_DEV_POOL contains nothing useful
118 - By default the tests suite will run xfs tests:
119 - ./check '*/001' '*/002' '*/003'
121 - Groups of tests maybe ran by: ./check -g [group(s)]
122 See the 'group' file for details on groups
123 - To randomize test order: ./check -r [test(s)]
124 - You can explicitly specify NFS/CIFS/OVERLAY, otherwise
125 the filesystem type will be autodetected from $TEST_DEV:
126 - for running nfs tests: ./check -nfs [test(s)]
127 - for running cifs/smb3 tests: ./check -cifs [test(s)]
128 - for overlay tests: ./check -overlay [test(s)]
129 The TEST and SCRATCH partitions should be pre-formatted
130 with another base fs, where the overlay dirs will be created
133 The check script tests the return value of each script, and
134 compares the output against the expected output. If the output
135 is not as expected, a diff will be output and an .out.bad file
136 will be produced for the failing test.
138 Unexpected console messages, crashes and hangs may be considered
139 to be failures but are not necessarily detected by the QA system.
141 __________________________
142 ADDING TO THE FSQA SUITE
143 __________________________
146 Creating new tests scripts:
148 Use the "new" script.
150 Test script environment:
152 When developing a new test script keep the following things in
153 mind. All of the environment variables and shell procedures are
154 available to the script once the "common/rc" file has been
157 1. The tests are run from an arbitrary directory. If you want to
158 do operations on an XFS filesystem (good idea, eh?), then do
159 one of the following:
161 (a) Create directories and files at will in the directory
162 $TEST_DIR ... this is within an XFS filesystem and world
163 writeable. You should cleanup when your test is done,
164 e.g. use a _cleanup shell procedure in the trap ... see
165 001 for an example. If you need to know, the $TEST_DIR
166 directory is within the filesystem on the block device
169 (b) mkfs a new XFS filesystem on $SCRATCH_DEV, and mount this
170 on $SCRATCH_MNT. Call the the _require_scratch function
171 on startup if you require use of the scratch partition.
172 _require_scratch does some checks on $SCRATCH_DEV &
173 $SCRATCH_MNT and makes sure they're unmounted. You should
174 cleanup when your test is done, and in particular unmount
176 Tests can make use of $SCRATCH_LOGDEV and $SCRATCH_RTDEV
177 for testing external log and realtime volumes - however,
178 these tests need to simply "pass" (e.g. cat $seq.out; exit
179 - or default to an internal log) in the common case where
180 these variables are not set.
182 2. You can safely create temporary files that are not part of the
183 filesystem tests (e.g. to catch output, prepare lists of things
184 to do, etc.) in files named $tmp.<anything>. The standard test
185 script framework created by "new" will initialize $tmp and
188 3. By default, tests are run as the same uid as the person
189 executing the control script "check" that runs the test scripts.
191 4. Some other useful shell procedures:
193 _get_fqdn - echo the host's fully qualified
196 _get_pids_by_name - one argument is a process name, and
197 return all of the matching pids on
200 _within_tolerance - fancy numerical "close enough is good
201 enough" filter for deterministic
202 output ... see comments in
203 common/filter for an explanation
205 _filter_date - turn ctime(3) format dates into the
206 string DATE for deterministic
209 _cat_passwd, - dump the content of the password
210 _cat_group or group file (both the local file
211 and the content of the NIS database
212 if it is likely to be present)
214 5. General recommendations, usage conventions, etc.:
215 - When the content of the password or group file is
216 required, get it using the _cat_passwd and _cat_group
217 functions, to ensure NIS information is included if NIS
219 - When calling getfacl in a test, pass the "-n" argument so
220 that numeric rather than symbolic identifiers are used in
222 - When creating a new test, it is possible to enter a custom name
223 for the file. Filenames are in form NNN-custom-name, where NNN
224 is automatically added by the ./new script as an unique ID,
225 and "custom-name" is the optional string entered into a prompt
226 in the ./new script. It can contain only alphanumeric characters
227 and dash. Note the "NNN-" part is added automatically.
231 Each test script has a name, e.g. 007, and an associated
232 verified output, e.g. 007.out.
234 It is important that the verified output is deterministic, and
235 part of the job of the test script is to filter the output to
236 make this so. Examples of the sort of things that need filtering:
243 - variable directory contents
244 - imprecise numbers, especially sizes and times
248 The script "check" may be used to run one or more tests.
250 Test number $seq is deemed to "pass" when:
251 (a) no "core" file is created,
252 (b) the file $seq.notrun is not created,
253 (c) the exit status is 0, and
254 (d) the output matches the verified output.
256 In the "not run" case (b), the $seq.notrun file should contain a
257 short one-line summary of why the test was not run. The standard
258 output is not checked, so this can be used for a more verbose
259 explanation and to provide feedback when the QA test is run
263 To force a non-zero exit status use:
269 won't have the desired effect because of the way the exit trap
272 The recent pass/fail history is maintained in the file "check.log".
273 The elapsed time for the most recent pass for each test is kept
276 The compare-failures script in tools/ may be used to compare failures
277 across multiple runs, given files containing stdout from those runs.
283 Send patches to the fstests mailing list at fstests@vger.kernel.org.