btrfs: add a test for some disk caching usecases

This is a test to check the behavior of the disk caching code inside
btrfs.  It's a regression test for the patch

  btrfs: allow single disk devices to mount with older generations

Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Eryu Guan <guaneryu@gmail.com>

diff --git a/tests/btrfs/219 b/tests/btrfs/219
new file mode 100755 (executable)
index 0000000..1dd327a
--- /dev/null
+++ b/tests/btrfs/219
@@ -0,0 +1,104 @@
+#! /bin/bash
+# SPDX-License-Identifier: GPL-2.0
+# Copyright (c) 2020 Facebook.  All Rights Reserved.
+#
+# FS QA Test 219
+#
+# Test a variety of stale device usecases.  We cache the device and generation
+# to make sure we do not allow stale devices, which can end up with some wonky
+# behavior for loop back devices.  This was changed with
+#
+#   btrfs: allow single disk devices to mount with older generations
+#
+# But I've added a few other test cases so it's clear what we expect to happen
+# currently.
+#
+
+seq=`basename $0`
+seqres=$RESULT_DIR/$seq
+echo "QA output created by $seq"
+
+here=`pwd`
+tmp=/tmp/$$
+status=1       # failure is the default!
+trap "_cleanup; exit \$status" 0 1 2 3 15
+
+_cleanup()
+{
+       cd /
+       rm -f $tmp.*
+       if [ ! -z "$loop_mnt" ]; then
+               $UMOUNT_PROG $loop_mnt
+               rm -rf $loop_mnt
+       fi
+       [ ! -z "$loop_mnt1" ] && rm -rf $loop_mnt1
+       [ ! -z "$fs_img1" ] && rm -rf $fs_img1
+       [ ! -z "$fs_img2" ] && rm -rf $fs_img2
+       [ ! -z "$loop_dev" ] && _destroy_loop_device $loop_dev
+}
+
+# get standard environment, filters and checks
+. ./common/rc
+. ./common/filter
+
+# remove previous $seqres.full before test
+rm -f $seqres.full
+
+# real QA test starts here
+
+_supported_fs btrfs
+_supported_os Linux
+_require_test
+_require_loop
+_require_btrfs_forget_or_module_loadable
+
+loop_mnt=$TEST_DIR/$seq.mnt
+loop_mnt1=$TEST_DIR/$seq.mnt1
+fs_img1=$TEST_DIR/$seq.img1
+fs_img2=$TEST_DIR/$seq.img2
+
+mkdir $loop_mnt
+mkdir $loop_mnt1
+
+$XFS_IO_PROG -f -c "truncate 256m" $fs_img1 >>$seqres.full 2>&1
+
+_mkfs_dev $fs_img1 >>$seqres.full 2>&1
+cp $fs_img1 $fs_img2
+
+# Normal single device case, should pass just fine
+_mount -o loop $fs_img1 $loop_mnt > /dev/null  2>&1 || \
+       _fail "Couldn't do initial mount"
+$UMOUNT_PROG $loop_mnt
+
+_btrfs_forget_or_module_reload
+
+# Now mount the new version again to get the higher generation cached, umount
+# and try to mount the old version.  Mount the new version again just for good
+# measure.
+loop_dev=`_create_loop_device $fs_img1`
+
+_mount $loop_dev $loop_mnt > /dev/null 2>&1 || \
+       _fail "Failed to mount the second time"
+$UMOUNT_PROG $loop_mnt
+
+_mount -o loop $fs_img2 $loop_mnt > /dev/null 2>&1 || \
+       _fail "We couldn't mount the old generation"
+$UMOUNT_PROG $loop_mnt
+
+_mount $loop_dev $loop_mnt > /dev/null 2>&1 || \
+       _fail "Failed to mount the second time"
+$UMOUNT_PROG $loop_mnt
+
+# Now we definitely can't mount them at the same time, because we're still tied
+# to the limitation of one fs_devices per fsid.
+_btrfs_forget_or_module_reload
+
+_mount $loop_dev $loop_mnt > /dev/null 2>&1 || \
+       _fail "Failed to mount the third time"
+_mount -o loop $fs_img2 $loop_mnt1 > /dev/null 2>&1 && \
+       _fail "We were allowed to mount when we should have failed"
+
+# success, all done
+echo "Silence is golden"
+status=0
+exit

diff --git a/tests/btrfs/219.out b/tests/btrfs/219.out
new file mode 100644 (file)
index 0000000..162074d
--- /dev/null
+++ b/tests/btrfs/219.out
@@ -0,0 +1,2 @@
+QA output created by 219
+Silence is golden

diff --git a/tests/btrfs/group b/tests/btrfs/group
index 3295856d0c8cc72ca995d696d58e07a54267893e..660cdc2519b72385ffc0da4057182f1b7a321fb6 100644 (file)
--- a/tests/btrfs/group
+++ b/tests/btrfs/group
@@ -221,3 +221,4 @@
 216 auto quick seed
 217 auto quick trim dangerous
 218 auto quick volume
+219 auto quick volume