doc/rados: fix outdated value for ms_bind_port_max

The highest port number used by OSD or MDS daemons was increased from
7300 to 7568 in [1] but the documentation still refers to 7300 in
multiple locations.

[1] https://github.com/ceph/ceph/pull/42210

Fixes: https://tracker.ceph.com/issues/65609
Signed-off-by: Pierre Riteau <pierre@stackhpc.com>
(cherry picked from commit 23d2740241af2118652fef6e7d6a286f338a18f2)

diff --git a/doc/rados/configuration/network-config-ref.rst b/doc/rados/configuration/network-config-ref.rst
index 81e85c5d1b2acf0ca4f56707bf1d3f89a8348124..252b43d67ff22ed9846091592715f536345a7b78 100644 (file)
--- a/doc/rados/configuration/network-config-ref.rst
+++ b/doc/rados/configuration/network-config-ref.rst
@@ -56,7 +56,7 @@ Recommendations - Networks`_ for additional details.
 IP Tables
 =========
 
-By default, daemons `bind`_ to ports within the ``6800:7300`` range. You may
+By default, daemons `bind`_ to ports within the ``6800:7568`` range. You may
 configure this range at your discretion. Before configuring your IP tables,
 check the default ``iptables`` configuration.
 
@@ -96,7 +96,7 @@ A :term:`Ceph Metadata Server` or :term:`Ceph Manager` listens on the first
 available port on the public network beginning at port 6800. Note that this 
 behavior is not deterministic, so if you are running more than one OSD or MDS
 on the same host, or if you restart the daemons within a short window of time,
-the daemons will bind to higher ports. You should open the entire 6800-7300
+the daemons will bind to higher ports. You should open the entire 6800-7568
 range by default.  When you add the rule using the example below, make sure
 you replace ``{iface}`` with the public network interface (e.g., ``eth0``,
 ``eth1``, etc.), ``{ip-address}`` with the IP address of the public network
@@ -106,7 +106,7 @@ For example:
 
 .. prompt:: bash $
 
-   sudo iptables -A INPUT -i {iface} -m multiport -p tcp -s {ip-address}/{netmask} --dports 6800:7300 -j ACCEPT
+   sudo iptables -A INPUT -i {iface} -m multiport -p tcp -s {ip-address}/{netmask} --dports 6800:7568 -j ACCEPT
 
 
 OSD IP Tables
@@ -136,7 +136,7 @@ Each Ceph OSD Daemon on a Ceph Node may use up to four ports:
               \---------------/
 
 When a daemon fails and restarts without letting go of the port, the restarted
-daemon will bind to a new port. You should open the entire 6800-7300 port range
+daemon will bind to a new port. You should open the entire 6800-7568 port range
 to handle this possibility.
 
 If you set up separate public and cluster networks, you must add rules for both
@@ -149,7 +149,7 @@ public or cluster network. For example:
 
 .. prompt:: bash $
 
-   sudo iptables -A INPUT -i {iface}  -m multiport -p tcp -s {ip-address}/{netmask} --dports 6800:7300 -j ACCEPT
+   sudo iptables -A INPUT -i {iface}  -m multiport -p tcp -s {ip-address}/{netmask} --dports 6800:7568 -j ACCEPT
 
 .. tip:: If you run Ceph Metadata Servers on the same Ceph Node as the 
    Ceph OSD Daemons, you can consolidate the public network configuration step. 
@@ -314,7 +314,7 @@ Bind
 ----
 
 Bind settings set the default port ranges Ceph OSD and MDS daemons use. The
-default range is ``6800:7300``. Ensure that your `IP Tables`_ configuration
+default range is ``6800:7568``. Ensure that your `IP Tables`_ configuration
 allows you to use the configured port range.
 
 You may also enable Ceph daemons to bind to IPv6 addresses instead of IPv4

diff --git a/doc/rados/troubleshooting/troubleshooting-mon.rst b/doc/rados/troubleshooting/troubleshooting-mon.rst
index 443d6c443bee3255d3ac7f75e0026ab5f1af9070..636bb4da2c02d9c6801dfe0e31880f3f9e3c3bef 100644 (file)
--- a/doc/rados/troubleshooting/troubleshooting-mon.rst
+++ b/doc/rados/troubleshooting/troubleshooting-mon.rst
@@ -493,10 +493,10 @@ trying to connect to Ceph daemons. For example::
 
 It might also be necessary to add rules to iptables on your Ceph hosts to
 ensure that clients are able to access the TCP ports associated with your Ceph
-monitors (default: port 6789) and Ceph OSDs (default: 6800 through 7300). For
+monitors (default: port 6789) and Ceph OSDs (default: 6800 through 7568). For
 example::
 
-    iptables -A INPUT -m multiport -p tcp -s {ip-address}/{netmask} --dports 6789,6800:7300 -j ACCEPT
+    iptables -A INPUT -m multiport -p tcp -s {ip-address}/{netmask} --dports 6789,6800:7568 -j ACCEPT
 
 
 Monitor Store Failures