Yan, Zheng [Wed, 7 Aug 2013 06:38:22 +0000 (14:38 +0800)]
store: Add (experimental) ZFS parallel journal support
This patch adds ZFS parallel journal support. It uses libzfs provided by
zfsonlinux to access ZFS' functionalities. To enable ZFS parallel journal
support, compile ceph by:
./configure --with-libzfs LIBZFS_CFLAGS="-I<libzfs header> -I<libspl header>"
make
Add following line to osd section of ceph.conf
filestore zfs_snap = 1
Note: ZFS (no mater parallel journal is enabled or not) does not support
direct IO. To use it as backend FS for OSD, you need to add following line
to osd section of ceph.conf
Laurent Barbe [Tue, 13 Aug 2013 15:16:35 +0000 (17:16 +0200)]
init-rbdmap: fix for recursive umount
Umount is not always done in the correct order.
For exemple in that case :
/dev/rbd1 on /myrbd
/dev/rbd2 on /myrbd/.snapshots/@GMT-2013.08.09-10.14.44
rbd2 should be umounted before rbd1
Gary Lowell [Tue, 6 Aug 2013 00:57:26 +0000 (17:57 -0700)]
Makefile.am: fix libglobal.la races
Several targets had libglobal.la in the _LDFLAGS macro definition
when it should have been in the _LDADD macro. Remove those occurrance
and add the LIBGLOBAL_LDA macro to the targets _LDADD instead.
Yehuda Sadeh [Mon, 12 Aug 2013 17:05:44 +0000 (10:05 -0700)]
rgw: fix multi delete
Fixes: #5931
Backport: bobtail, cuttlefish
Fix a bad check, where we compare the wrong field. Instead of
comparing the ret code to 0, we compare the string value to 0
which generates implicit casting, hence the crash.
Sage Weil [Sat, 10 Aug 2013 01:02:32 +0000 (18:02 -0700)]
ceph-disk: fix mount options passed to move_mount
Commit 6cbe0f021f62b3ebd5f68fcc01a12fde6f08cff5 added a mount_options but
in certain cases it may be blank. Fill in with the defaults, just as we
do in mount().
Backport: cuttlefish Reviewed-by: Dan Mick <dan.mick@inktank.com> Signed-off-by: Sage Weil <sage@inktank.com>
common: pick_addresses: fix bug with observer class that triggered #5205
The Observer class we defined to observe conf changes and thus avoid
triggering #5205 (as fixed by eb86eebe1ba42f04b46f7c3e3419b83eb6fe7f9a),
was returning always the same const static array, which would lead us to
always populate the observer's list with an observer for 'public_addr'.
This would of course become a problem when trying to obtain the observer
for 'cluster_add' during md_config_t::set_val() -- thus triggering the
same assert as initially reported on #5205.
Backport: cuttlefish Fixes: #5205 Signed-off-by: Joao Eduardo Luis <jecluis@gmail.com> Reviewed-by: Sage Weil <sage@inktank.com>
Yehuda Sadeh [Fri, 9 Aug 2013 18:52:25 +0000 (11:52 -0700)]
rgw: return 423 Locked response when failing to lock object
Fixes: #5882
Translate the EBUSY we get when trying to lock a shard / object
to 423 Locked response. Beforehand it was just translated to the
default 500.
Reviewed-by: Sage Weil <sage@inktank.com> Signed-off-by: Yehuda Sadeh <yehuda@inktank.com>
Yehuda Sadeh [Fri, 9 Aug 2013 16:31:28 +0000 (09:31 -0700)]
rgw: rename data receive callbacks in swift token revocation
Fixes: #5921
As part of the work that was made for dumpling, the http
client in-data callback was renamed in order to avoid confusion.
However, we missed the rename in a couple of places, which this
patch amend.
Reported-by: Roald van Loon <roaldvanloon@gmail.com> Reviewed-by: Sage Weil <sage@inktank.com> Signed-off-by: Yehuda Sadeh <yehuda@inktank.com>
Dan Mick [Tue, 6 Aug 2013 01:18:59 +0000 (18:18 -0700)]
ceph.in: Re-enable ceph interactive mode (missing its output).
Also, loop on error. There's no reason to exit the interpreter loop on
an error, and it's probably less annoying if we don't. Print the error,
and any output, and continue.
Fixes: #5746 Signed-off-by: Dan Mick <dan.mick@inktank.com>
Sage Weil [Thu, 8 Aug 2013 15:30:01 +0000 (08:30 -0700)]
mon: fix 'osd crush rule rm ...' dup arg
This was broken way back in 0d66c9ebbf626117c641c975a8682a0aaba588c4, but
we were ignoring the dup until recently.
t Signed-off-by: Sage Weil <sage@inktank.com>
If an entity already existed, 'auth add' would smash its key and caps
with whatever was on the supplied keyring file; if a keyring weren't
specified, we would simply generate a new key and destroy all existing
caps (unless caps were specified and happened to be different from the
already in-place caps). This behaviour is obviously sketchy.
With this patch we now enforce the following behaviour:
- if entity does not exist in current state, check if we are about to
create it (by checking the pending state); if so, wait for the new state
to be committed and re-handle the command then, so we don't get bad
results from pending request
- if the command reproduces the current state (same key, same caps), we
return 0; else,
- if entity exists and supplied key OR caps are different, return -EINVAL
- else create a new entity.
Signed-off-by: Joao Eduardo Luis <joao.luis@inktank.com> Reviewed-by: Sage Weil <sage@inktank.com>
Dan Mick [Sat, 3 Aug 2013 04:26:51 +0000 (21:26 -0700)]
mon/PGMonitor: add 'pg dump pgs_brief' subcommand
It is useful to map OSDs to PGs and vice-versa; pg dump gives that
information, but gives a lot of other stuff. This is the same dump
as pg dump pgs, but omitting everything except pgid, state, and
osd up and acting sets.
Signed-off-by: Dan Mick <dan.mick@inktank.com> Reviewed-by: Sage Weil <sage@inktank.com>
Dan Mick [Sat, 3 Aug 2013 03:46:00 +0000 (20:46 -0700)]
ceph_argparse.py: add stderr note if nonrequired param is invalid
If we run across a user-supplied parameter that doesn't validate against
a non-required descriptor, it may be that it's a valid entry for a later
descriptor...or it may be that it's supposed to match. We can't really tell.
A possible heuristic would be to call it invalid-for-sure if we're at the
end of the descriptor list, but that's not very generic.
Warn about it and try to drive on anyway.
Signed-off-by: Dan Mick <dan.mick@inktank.com> Reviewed-by: Sage Weil <sage@inktank.com>
Dan Mick [Fri, 2 Aug 2013 05:35:08 +0000 (22:35 -0700)]
Fix "too few args validate"
Check that number of validated arguments matches the number of required
arguments in the signature. Also, sort all possible matches by
length of signature. This way "ceph osd crush set" and
"ceph osd crush set <args>" can work while still insisting that
extra args or too few args are errors.
Also, restructure and factor out some of the work of validate() to make
its inner loop smaller and hopefully more comprehensible.
Signed-off-by: Dan Mick <dan.mick@inktank.com> Reviewed-by: Sage Weil <sage@inktank.com>
commit 0071b8e75b (mds: stay in SCAN state in file_eval) makes
Locker::file_eval() ignore lock in LOCK_SCAN state. If there
is no request changes the lock state, the lock can be stuck in
LOCK_SCAN state forever. This can cause client read/write hang
because lock in LOCK_SCAN state does not allow Frw caps.
The fix is change LOCK_SCAN to a unstable state. Thank to the
CInode::STATE_RECOVERING check in Locker::eval_gather(), the
lock stays in the SCAN state while file is being recovering.
The lock will transit to a stable state once the recovery
finishes.
mds: handle "state == LOCK_LOCK_XLOCK" when cancelling xlock
If we find lock state is LOCK_LOCK_XLOCK when cancelling xlock,
set lock state to LOCK_XLOCK_DONE and call Locker::eval_gather().
This makes sure the lock will eventually transit to a stable state.
(LOCK_XLOCK_DONE's next state is stable)
projects / ceph.git / log